Module Outline
Date retreived
22/07/2026 9:36 PM AWST
22/07/2026 9:36 PM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Plant Mechanics (Indust.agric) App 2a
Plant Mechanics (Indust.agric) App 2a
Module
National Code
State Code
87228
87228
DTWD Status
Approved
Approved
State Implementation and Classification
Approved Date
Field of Education
Nominal Hours
144
Description
To teach the principle of operation, construction,
assembly and disassembly procedures of components
and assemblies of typical industrial and
agricultural plant equipment, and theoretical
knowledge required for repair and diagnostic skills.
To practice skill development, to supplement
employer training.
assembly and disassembly procedures of components
and assemblies of typical industrial and
agricultural plant equipment, and theoretical
knowledge required for repair and diagnostic skills.
To practice skill development, to supplement
employer training.
No information
Evidence Guide
Examination 100%
Internal Practical Assessment 100%
Examination will consist of one paper, at the
completion of the three-week block of training. The
examination is to be of two hours' duration, and
will comprise of:
Seventy objective type questions 70 marks
Six short essay type questions 30 marks
Practical - The practical mark is to be an
assessment of the student's attitude, involvement
and interest, displayed in theory, demonstration and
practical sessions throughout each stage of
training, and is to be expressed as a percentage.
NOTE: Practical objectives throughout this syllabus, indicate the tasks,
which will be carried out during practical training sessions.
It is not intended that all students be individually
assessed in each practical objective.
Formula -Exam mark is to be certificate %.
Certificate of Trade Studies
To be eligible for this certificate, an apprentice
must reach a pass standard in the certificate
percentage, at the end of each stage.
Privileged Re-Examination - may be granted
on the recommendation of a Board of Review, when the
practical assessment is satisfactory.
NOTE: A separate privileged re-examination will be normally set.
The examination will consist of one paper of two
hours' duration, and will comprise of:
Seventy objective type questions 70 marks
Six short essay type questions 30 marks
Students granted privileged re-examination, will not
be required to repeat the three-week period of
training.
Internal Practical Assessment 100%
Examination will consist of one paper, at the
completion of the three-week block of training. The
examination is to be of two hours' duration, and
will comprise of:
Seventy objective type questions 70 marks
Six short essay type questions 30 marks
Practical - The practical mark is to be an
assessment of the student's attitude, involvement
and interest, displayed in theory, demonstration and
practical sessions throughout each stage of
training, and is to be expressed as a percentage.
NOTE: Practical objectives throughout this syllabus, indicate the tasks,
which will be carried out during practical training sessions.
It is not intended that all students be individually
assessed in each practical objective.
Formula -Exam mark is to be certificate %.
Certificate of Trade Studies
To be eligible for this certificate, an apprentice
must reach a pass standard in the certificate
percentage, at the end of each stage.
Privileged Re-Examination - may be granted
on the recommendation of a Board of Review, when the
practical assessment is satisfactory.
NOTE: A separate privileged re-examination will be normally set.
The examination will consist of one paper of two
hours' duration, and will comprise of:
Seventy objective type questions 70 marks
Six short essay type questions 30 marks
Students granted privileged re-examination, will not
be required to repeat the three-week period of
training.
Elements and Performance Criteria
No information
No information
Associated Qual/Courses
| State Code | National Code | Title | Type |
|---|---|---|---|
| 1078 | Fuel Injection Fitting | Accredited course | |
| 1157 | Plant Mechanic (Agricultural) | Accredited course | |
| 1140 | Plant Mechanic (Industrial) | Accredited course |