Unit of competency Outline

Date retreived
23/07/2026 4:20 PM AWST

Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.

Licence to operate a non-slewing mobile crane (greater than 3 tonnes capacity)

Licence to operate a non-slewing mobile crane (greater than 3 tonnes capacity)

Unit of competency
National Code
TLILIC3006
State Code
AWL66
TGA Status
Replaced
DTWD Status
Replaced
Current Release Number
1.00
Current Release Date
29/02/2016
View on TGA
State Implementation and Classification
Approved Date
04/08/2016
Field of Education
030717 - Plant And Machine Operations
Original Release Date
04/08/2016
Nominal Hours
60
Description
This unit specifies the skills and knowledge required to operate a non-slewing mobile crane safely.Non-slewing mobile crane means a mobile crane incorporating a boom or jib that cannot be slewed, and includes:an articulated mobile cranea locomotive cranebut does not include vehicle tow trucks.This unit applies to the activities of a person operating a non-slewing crane with a capacity exceeding 3 tonnes.A person performing this work is required to hold a non-slewing mobile crane high risk work (HRW) licence.This unit requires a person operating non-slewing mobile crane to plan the work, conduct routine checks, set up crane, transfer load, mobile load and shut down and secure crane. Licensing/Regulatory InformationThis unit is based on the licensing requirements of Part 4.5 of the Model Work Health and Safety (WHS) Regulations, HRW and meets Commonwealth, state and territory HRW licensing requirements. Any alteration to this unit would result in a unit that would not be acceptable to work health and safety (WHS)/occupational health and safety (OHS) regulators for the purpose of licensing.
Notes
Elements and Performance Criteria
1 Plan work
  • 1.1 Potential workplace hazards are identified
  • 1.2 Hazard control measures are identified consistent with appropriate standards to ensure the safety of personnel and equipment
  • 1.3 Weight of load is identified and estimated in consultation with associated personnel
  • 1.4 Crane is appropriate to the load/s and workplace conditions
  • 1.5 Appropriate path for moving loads in work area is inspected and determined
  • 1.6 Appropriate communications methods are identified in consultation with associated personnel
2 Conduct routine checks
  • 2.1 Crane is visually checked for any damage or defects
  • 2.2 Crane is accessed in a safe manner
  • 2.3 All signage and labels are checked to ensure they are visible and legible in accordance with the appropriate standard
  • 2.4 Routine pre-operational crane checks are carried out in accordance with procedures
  • 2.5 All controls are located and identified
  • 2.6 Crane service logbook is checked for compliance
  • 2.7 Crane is started in accordance with procedures and is checked for any abnormal noises
  • 2.8 All crane safety devices are tested in accordance with procedures
  • 2.9 Post-start operational checks are carried out in accordance with procedures
  • 2.10 All communications equipment is checked for serviceability
  • 2.11 All damage and defects are reported and recorded in accordance with procedures, and appropriate action is taken
3 Set up crane
  • 3.1 Ground suitability is checked
  • 3.2 Crane is driven to work area in accordance with procedures
  • 3.3 Crane is positioned for work application and stability in accordance with procedures
  • 3.4 Appropriate crane configuration for work task is determined in accordance with procedures
  • 3.5 Boom/jib and counterweight configuration data is input into crane computer as required
  • 3.6 Appropriate hazard prevention/control measures are applied to work area in accordance with procedures
  • 3.7 All communications equipment is tested for functionality
4 Transfer load
  • 4.1 Lifts are determined within the capacity of the crane
  • 4.2 Boom/jib and hoist block is positioned over load following directions from associated personnel
  • 4.3 Test lift is carried out in accordance with procedures to allow for checks to be safely made, in consultation with relevant personnel
  • 4.4 Loads are transferred using all relevant crane movements in accordance with procedures and the appropriate standard
  • 4.5 All required communications signals are correctly interpreted in accordance with procedures and the appropriate standard
  • 4.6 Crane is operated in accordance with procedures
  • 4.7 Load movement is monitored constantly, to ensure safety of personnel and load, and crane stability
  • 4.8 Unplanned and/or unsafe situations are responded to in accordance with procedures
5 Mobile load
  • 5.1 Suitability of planned route for crane is checked in accordance with procedures
  • 5.2 Crane is configured to mobile load in accordance with procedures
  • 5.3 Load is moved using best mobile practice in accordance with the appropriate standard
6 Shut down and secure crane
  • 6.1 Crane boom/jib and equipment are stowed and secured as required, in accordance with procedures and the appropriate standard
  • 6.2 Relevant motion locks and brakes are applied as required
  • 6.3 Outriggers/stabilisers are stowed and secured as required in accordance with procedures
  • 6.4 Crane is shut down in accordance with procedures
  • 6.5 Routine post-operational crane checks are carried out in accordance with procedures
  • 6.6 Plates or packing are stowed and secured as required
  • 6.7 All damage and defects are recorded and reported in accordance with procedures, and appropriate action is taken
No information
No information
Replaces
State Code National Code Title Type
D5249 TLILIC3006A Licence to operate a non-slewing mobile crane (greater than 3 tonnes capacity) Unit of competency
Replaced By
State Code National Code Title Type
OAE46 TLILIC0008 Licence to operate a non-slewing mobile crane (greater than 3 tonnes capacity) Unit of competency