Unit of competency Outline
Date retreived
22/07/2026 5:52 AM AWST
22/07/2026 5:52 AM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Operate and monitor valve systems
Operate and monitor valve systems
Unit of competency
National Code
PMAOPS223A
PMAOPS223A
State Code
C5954
C5954
TGA Status
Replaced
Replaced
DTWD Status
Replaced
Replaced
State Implementation and Classification
Approved Date
23/04/2004
Field of Education
030717 - Plant And Machine Operations
Original Release Date
23/04/2004
Nominal Hours
20
Description
In a typical scenario an operator adjusts and monitors valves and ancillary equipment as part of controlling a process (e.g. hydrocarbons transport pipeline, gas distribution network). This unit may be required when PMAOPS222A - Operate and monitor pumping systems and equipment is appropriate. It may only be counted towards a qualification where competence in PMAOPS201A - Operate fluid flow equipment is unable to be obtained due to the nature of the job, but the operation of valves is relevant.The operations technician would:identify and report operational problems be aware of and contribute to a safe working environment contribute to the safe and productive operation of the valve operate, monitor and maintain equipment using relevant proceduresGenerally the operator would be part of a team and would be expected to be competent in all parts of this unit. At all times they would be liaising and cooperating with other members of the team/shift.PrerequisitesThis unit does not have prerequisites:In a typical scenario an operator adjusts and monitors valves and ancillary equipment as part of controlling a process (e.g. hydrocarbons transport pipeline, gas distribution network). This unit may be required when PMAOPS222A - Operate and monitor pumping systems and equipment is appropriate. It may only be counted towards a qualification where competence in PMAOPS201A - Operate fluid flow equipment is unable to be obtained due to the nature of the job, but the operation of valves is relevant.The operations technician would:identify and report operational problems be aware of and contribute to a safe working environment contribute to the safe and productive operation of the valve operate, monitor and maintain equipment using relevant proceduresGenerally the operator would be part of a team and would be expected to be competent in all parts of this unit. At all times they would be liaising and cooperating with other members of the team/shift.PrerequisitesThis unit does not have prerequisites:
Notes
Elements and Performance Criteria
1 Prepare valves for operation
- 1.1 Check operation of valves and valve systems by applying knowledge of valve operation and fundamental operating principles.
- 1.2 Check the valves required for operation against the site specific operating pressures, temperatures, volume, velocities and materials requirements where applicable.
- 1.3 Prepare or sequence valves required for operation, ensuring that they are either closed or opened as required, to regulate the flow of liquids and systems flow rates in a safe and efficient manner.
- 1.4 Check the valve's operational integrity to minimise the risk of valve leakages and failures.
2 Operate valve systems
- 2.1 Monitor valve operation to ensure it is functioning correctly and excludes such incidents as vibration, chatter, cycling, and sticking.
- 2.2 Regulate or alter valve sequences to control the flow rates of fluid during the process to meet changing production conditions and demands.
3 Conduct operational maintenance
- 3.1 Clean and lubricate valve stems, threads and other operational parts to ensure the correct operational condition of the valve is maintained.
- 3.2 Evenly tighten valve bolting assembles to prevent product leakage.
- 3.3 Identify valve and regulator faults and take appropriate action.
- 3.4 Isolate jammed or sticking valves from operation, report and prepare for maintenance.
4 Control hazards
- 4.1 Identify hazards in work area.
- 4.2 Assess the risks arising from those hazards.
- 4.3 Implement measures to control those risks in line with procedures and duty of care.
5 Respond to valve problems
- 5.1 Monitor plant frequently and critically throughout shift using measured/indicated data and senses (sight, hearing, etc.) as appropriate.
- 5.2 Recognise operational problems.
- 5.3 Analyse cause of operational problems within scope of skill level.
- 5.4 Take timely and appropriate action to solve operational problems.
Context
This unit of competency includes all such items of equipment and unit operations which form part of the valve system.
For your plant this may include (select relevant items):
globe, butterfly, ball and gate valves
control valves
isolation valves
non-return or check valves
pressure relief valves
shutdown systems
hydraulic power units.
Valve actuation may be:
pneumatic
hydraulic
electrical
manual.
Typical problems for your plant may include:
vibration/resonance
blockages/hydrates
valve seat wear
valve seal leakage
valve stem leakage
mechanical failure, e.g. plug/gate
valve sticking.
HSE
All operations to which this unit applies are subject to stringent health, safety and environment requirements, which may be imposed through State or Federal legislation, and these must not be compromised at any time. Where there is an apparent conflict between performance criteria and HSE requirements, the HSE requirements take precedence.
This unit of competency includes all such items of equipment and unit operations which form part of the valve system.
For your plant this may include (select relevant items):
globe, butterfly, ball and gate valves
control valves
isolation valves
non-return or check valves
pressure relief valves
shutdown systems
hydraulic power units.
Valve actuation may be:
pneumatic
hydraulic
electrical
manual.
Typical problems for your plant may include:
vibration/resonance
blockages/hydrates
valve seat wear
valve seal leakage
valve stem leakage
mechanical failure, e.g. plug/gate
valve sticking.
HSE
All operations to which this unit applies are subject to stringent health, safety and environment requirements, which may be imposed through State or Federal legislation, and these must not be compromised at any time. Where there is an apparent conflict between performance criteria and HSE requirements, the HSE requirements take precedence.
Assessment context and methods
Assessment for this unit of competency will be on an operating plant. The unit will be assessed in as holistic a manner as is practical and may be integrated with the assessment of other relevant units of competency. Assessment will occur over a range of situations, which will include disruptions to normal, smooth operation.
Simulation may be required to allow for timely assessment of parts of this unit of competency (e.g. element 3). Simulation should be based on the actual plant and will include walk throughs of the relevant competency components. Simulations may also include the use of case studies/scenarios, role plays and 3D virtual reality interactive systems. In the case of evacuation training or of training for competencies practised in life threatening situations, simulation may be used for the bulk of the training.
This unit of competency requires an application of the knowledge contained in the use of valve systems and their integral equipment, to the level needed to maintain control and recognise and resolve problems. This can be assessed through questioning and the use of what if scenarios both on the plant (during demonstration of normal operations and walk throughs of abnormal operations) and off the plant.
Critical aspects
Competence must be demonstrated in the ability to recognise and analyse potential situations requiring action and then in implementing appropriate corrective action. The emphasis should be on the ability to stay out of trouble rather than on recovery from a disaster.
Consistent performance should be demonstrated. In particular look to see that:
early warning signs of equipment/processes needing attention or with potential problems are recognised
the range of possible causes can be identified and analysed and the most likely cause determined
appropriate action is taken to ensure a timely return to full performance
obvious problems in related plant areas are recognised and an appropriate contribution made to their solution.
These aspects may be best assessed using a range of scenarios/case studies/what ifs as the stimulus with a walk through forming part of the response. These assessment activities should include a range of problems, including new, unusual and improbable situations, which may have been generated from the past incident history of valves, incidents with similar valves around the world, hazard analysis activities and similar sources.
Resource implications
As a general rule assessment will require access to an operating plant over an extended period of time, or a suitable method of gathering evidence of operating competence over a range of situations. A bank of scenarios/case studies/what ifs will be required as will a bank of questions which will be used to probe the reasoning behind the observable actions.
Other assessment advice
In all plants it may be appropriate to assess this unit concurrently with relevant teamwork and communication units. It will frequently also be appropriate to assess this unit concurrently with:
PMAOPS221A - Operate and monitor pumping systems and equipment
Essential knowledge
The knowledge referred to in the evidence guide for this unit includes:
identify all items on a schematic of the valve system and describe the function of each
physics related to the process
valve equipment operating parameters
process and product variables and reactions
operating pressures
operating temperatures
flow volume calculations
flow velocity calculations
fluid corrosive properties
fluid erosive properties.
Competence also includes the ability to isolate the causes of problems to an item of equipment within the valve system and distinguish between causes of problems/alarm/fault indications such as:
instrument failure/malfunction
electrical failure/malfunction
mechanical failure/malfunction
equipment design deficiencies (e.g. wrong valve type for service)
product parameters (e.g. temperature, viscosity, purity)
fouling or contamination
erosion and corrosion.
Assessment for this unit of competency will be on an operating plant. The unit will be assessed in as holistic a manner as is practical and may be integrated with the assessment of other relevant units of competency. Assessment will occur over a range of situations, which will include disruptions to normal, smooth operation.
Simulation may be required to allow for timely assessment of parts of this unit of competency (e.g. element 3). Simulation should be based on the actual plant and will include walk throughs of the relevant competency components. Simulations may also include the use of case studies/scenarios, role plays and 3D virtual reality interactive systems. In the case of evacuation training or of training for competencies practised in life threatening situations, simulation may be used for the bulk of the training.
This unit of competency requires an application of the knowledge contained in the use of valve systems and their integral equipment, to the level needed to maintain control and recognise and resolve problems. This can be assessed through questioning and the use of what if scenarios both on the plant (during demonstration of normal operations and walk throughs of abnormal operations) and off the plant.
Critical aspects
Competence must be demonstrated in the ability to recognise and analyse potential situations requiring action and then in implementing appropriate corrective action. The emphasis should be on the ability to stay out of trouble rather than on recovery from a disaster.
Consistent performance should be demonstrated. In particular look to see that:
early warning signs of equipment/processes needing attention or with potential problems are recognised
the range of possible causes can be identified and analysed and the most likely cause determined
appropriate action is taken to ensure a timely return to full performance
obvious problems in related plant areas are recognised and an appropriate contribution made to their solution.
These aspects may be best assessed using a range of scenarios/case studies/what ifs as the stimulus with a walk through forming part of the response. These assessment activities should include a range of problems, including new, unusual and improbable situations, which may have been generated from the past incident history of valves, incidents with similar valves around the world, hazard analysis activities and similar sources.
Resource implications
As a general rule assessment will require access to an operating plant over an extended period of time, or a suitable method of gathering evidence of operating competence over a range of situations. A bank of scenarios/case studies/what ifs will be required as will a bank of questions which will be used to probe the reasoning behind the observable actions.
Other assessment advice
In all plants it may be appropriate to assess this unit concurrently with relevant teamwork and communication units. It will frequently also be appropriate to assess this unit concurrently with:
PMAOPS221A - Operate and monitor pumping systems and equipment
Essential knowledge
The knowledge referred to in the evidence guide for this unit includes:
identify all items on a schematic of the valve system and describe the function of each
physics related to the process
valve equipment operating parameters
process and product variables and reactions
operating pressures
operating temperatures
flow volume calculations
flow velocity calculations
fluid corrosive properties
fluid erosive properties.
Competence also includes the ability to isolate the causes of problems to an item of equipment within the valve system and distinguish between causes of problems/alarm/fault indications such as:
instrument failure/malfunction
electrical failure/malfunction
mechanical failure/malfunction
equipment design deficiencies (e.g. wrong valve type for service)
product parameters (e.g. temperature, viscosity, purity)
fouling or contamination
erosion and corrosion.
Replaces
| State Code | National Code | Title | Type |
|---|---|---|---|
| C0867 | PMAHYD203A | Operate and monitor valve systems | Unit of competency |
Replaced By
| State Code | National Code | Title | Type |
|---|---|---|---|
| W8856 | PMAOPS223B | Operate and monitor valve systems | Unit of competency |
| State Code | National Code | Title | Type |
|---|---|---|---|
| W170 | MNM20305 | Certificate II in Metalliferous Mining Operations - Processing | Qualification |
| W347 | MNM20306 | Certificate II in Metalliferous Mining Operations (Processing) | Qualification |
| 3678 | 51575 | Certificate II in Mining for Entry Level Indigenous Workers | Accredited course |
| C650 | PMA30102 | Certificate III in Process Plant Operations | Qualification |
| C652 | PMA40102 | Certificate IV in Process Plant Technology | Qualification |