Unit of competency Outline
Date retreived
22/07/2026 1:50 AM AWST
22/07/2026 1:50 AM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Apply surface coatings by hand
Apply surface coatings by hand
Unit of competency
National Code
LMFFF2008B
LMFFF2008B
State Code
W8513
W8513
TGA Status
Replaced
Replaced
DTWD Status
Replaced
Replaced
State Implementation and Classification
Approved Date
19/09/2008
Field of Education
030117 - Furniture Polishing
Original Release Date
19/09/2008
Nominal Hours
40
Description
This unit covers the competency to apply brushable coatings, including one-pot polyurethane, enamels, acrylics and polish, by hand.
Notes
Elements and Performance Criteria
1. Prepare for work
- 1.1. Workplace information, including materials application and safety information, material safety data sheets is used to inform work practices
- 1.2. Characteristics of the surface and the required surface finish are identified from work orders or instructions
- 1.3. Processing and application techniques, time and safety requirements are identified and used for work planning
- 1.4. OHS requirements, including ventilation requirements and personal protection needs, are observed throughout the work
- 1.5. Tools, equipment and accessories are identified and checked for safe and effective operation for the surface finishing task
2. Prepare for application of materials
- 2.1. Surfaces are checked for contamination and correct preparation according to workplace procedures and standards
- 2.2. Products with surface or other faults are identified and faults repaired as appropriate
- 2.3. Finishing materials required are identified and prepared for the task
- 2.4. Trial applications of surface materials are made to check equipment operation, materials consistency and specified surface finish
- 2.5. Faults are identified and workplace procedures for rectification are followed
3. Apply finishing materials
- 3.1. Techniques for hand application of materials are identified
- 3.2. Finishing materials are applied according to job instructions, material manufacturer specifications and workplace procedures
- 3.3. Finished products are inspected and approved for suitability for further processing
- 3.4. Products which do not meet quality specifications are refinished or tagged for further investigation
4. Clean work area and maintain equipment
- 4.1. Equipment used is cleaned and inspected for serviceable condition and stored appropriately
- 4.2. Unserviceable equipment is tagged, faults are identified and appropriate personnel are informed
- 4.3. Work area is cleaned and returned to approved condition
- 4.4. Workplace records are completed
RANGE STATEMENT
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Unit context
OHS requirements may include legislation, building codes, material safety management systems, hazardous substance and dangerous goods codes and local safe operating procedures
Work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements
Work requires individuals to demonstrate discretion, judgement and problem solving skills in the application of surface coatings
Coatings are to include:
one-pot polyurethane
enamel
acrylic and polish
Application methods are to include:
brush and swooge
Surfaces may include but are not limited to:
solid timber
manufactured board
metal
Tools and equipment may include, but are not limited to:
sanders
pneumatic or low-voltage electric buff
rubber sanding block
brushes and swooges
Materials may include but are not limited to:
water
detergent
wax
oil
enamel
acrylic
one-pot polyurethane
polish
methylated spirits
turpentine
terebine
abrasive papers
cotton rags
steel wool
Personal protective equipment
Personal protective equipment is to include that prescribed under legislation, regulations and enterprise policies and practices
Information and procedures
Workplace procedures relating to the use and operation of tools and equipment
Workplace instructions, including job sheets, plans, drawings and designs
Workplace procedures relating to reporting and communications
Manufacturer specifications and operational procedures
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Unit context
OHS requirements may include legislation, building codes, material safety management systems, hazardous substance and dangerous goods codes and local safe operating procedures
Work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements
Work requires individuals to demonstrate discretion, judgement and problem solving skills in the application of surface coatings
Coatings are to include:
one-pot polyurethane
enamel
acrylic and polish
Application methods are to include:
brush and swooge
Surfaces may include but are not limited to:
solid timber
manufactured board
metal
Tools and equipment may include, but are not limited to:
sanders
pneumatic or low-voltage electric buff
rubber sanding block
brushes and swooges
Materials may include but are not limited to:
water
detergent
wax
oil
enamel
acrylic
one-pot polyurethane
polish
methylated spirits
turpentine
terebine
abrasive papers
cotton rags
steel wool
Personal protective equipment
Personal protective equipment is to include that prescribed under legislation, regulations and enterprise policies and practices
Information and procedures
Workplace procedures relating to the use and operation of tools and equipment
Workplace instructions, including job sheets, plans, drawings and designs
Workplace procedures relating to reporting and communications
Manufacturer specifications and operational procedures
EVIDENCE GUIDE
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Critical Aspects of Evidence
Interpret work order and locate and apply relevant information
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Follow work instructions, operating procedures and inspection practices to:
minimise the risk of injury to self and others
prevent damage to goods, equipment and products
maintain required production output and product quality
Prepare for and apply coatings by hand on a minimum of five occasions covering:
the three surface types
the four coatings detailed in the Range Statement
Maintain application equipment
Work effectively with others
Modify activities to cater for variations in workplace contexts and environment
Resource Implications
Hand finishing application equipment, coating materials, waxes and oils and surfaces to be coated.
Method of Assessment
Assessment methods must confirm consistency of performance over time and in a range of workplace relevant contexts.
Assessment should be by direct observation of tasks and questioning on underpinning knowledge.
Assessment may be in conjunction with assessment of other relevant units of competency.
Context of Assessment
Assessment may occur on the job or in a workplace simulated facility with relevant process equipment, materials, work instructions and deadlines.
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Critical Aspects of Evidence
Interpret work order and locate and apply relevant information
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Follow work instructions, operating procedures and inspection practices to:
minimise the risk of injury to self and others
prevent damage to goods, equipment and products
maintain required production output and product quality
Prepare for and apply coatings by hand on a minimum of five occasions covering:
the three surface types
the four coatings detailed in the Range Statement
Maintain application equipment
Work effectively with others
Modify activities to cater for variations in workplace contexts and environment
Resource Implications
Hand finishing application equipment, coating materials, waxes and oils and surfaces to be coated.
Method of Assessment
Assessment methods must confirm consistency of performance over time and in a range of workplace relevant contexts.
Assessment should be by direct observation of tasks and questioning on underpinning knowledge.
Assessment may be in conjunction with assessment of other relevant units of competency.
Context of Assessment
Assessment may occur on the job or in a workplace simulated facility with relevant process equipment, materials, work instructions and deadlines.
Replaces
| State Code | National Code | Title | Type |
|---|---|---|---|
| W0260 | LMFFF2008A | Apply surface coatings by hand | Unit of competency |
Replaced By
| State Code | National Code | Title | Type |
|---|---|---|---|
| WI320 | MSFFF2008 | Apply surface coatings by hand | Unit of competency |
| State Code | National Code | Title | Type |
|---|---|---|---|
| W030 | LMF30202 | Certificate III in Furniture Finishing | Qualification |
| W022 | LMF20202 | Certificate II in Furniture Finishing | Qualification |