Unit of competency Outline

Date retreived
23/07/2026 12:56 PM AWST

Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.

Set computer controlled machines/processes

Set computer controlled machines/processes

Unit of competency
National Code
MEM07015B
State Code
W5360
TGA Status
Replaced
DTWD Status
Replaced
Current Release Number
1.00
Current Release Date
01/12/2005
View on TGA
State Implementation and Classification
Approved Date
24/01/2012
Field of Education
030707 - Metal Fitting, Turning And MacHining
Original Release Date
24/01/2012
Nominal Hours
18
Description
This unit covers mounting work holding fixtures/devices/tools, conducting pre-start checks, setting numerical and computer controlled machines, instructing the operator and replacing worn or damaged tooling.
Notes
Elements and Performance Criteria
1. Obtain job instructions
  • 1.1. Job sheets or equivalent instructions are understood and correctly followed.
2. Mount work holding fixtures/devices/tools
  • 2.1. Machine is prepared to accept work holding fixtures/devices/tools.
  • 2.2. Preset tooling is mounted as required into machine/equipment.
  • 2.3. Work holding fixtures/devices are set on machine as required using standard operating procedures.
  • 2.4. Tool offset or datum settings are identified/verified against job sheet using standard operating procedures.
  • 2.5. Program is loaded, selected and verified in accordance with job instructions.
3. Conduct pre-start checks
  • 3.1. Pre-start checks are undertaken to standard operating procedures.
  • 3.2. Correct safety procedures are observed and all safety equipment is checked for correct operation.
4. Set machine
  • 4.1. Machine is set/adjusted to meet operational requirements and specifications.
  • 4.2. Production samples are checked for compliance with specifications using standard operating procedures.
5. Instruct machine operator
  • 5.1. Operator is instructed, if necessary, ensuring that all safety procedures and devices are in place.
6. Replace worn/damaged tooling
  • 6.1. Where appropriate, preset tools are replaced, tool offsets are adjusted or other corrective action is taken using standard operating procedures.
RANGE STATEMENT
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
EVIDENCE GUIDE
The evidence guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Overview of assessment
A person who demonstrates competency in this unit must be able to set computer controlled machines/processes. Competency in this unit cannot be claimed until all prerequisites have been satisfied.
Critical aspects for assessment and evidence required to demonstrate competency in this unit
Assessors must be satisfied that the candidate can competently and consistently perform all elements of the unit as specified by the criteria, including required knowledge, and be capable of applying the competency in new and different situations and contexts.
Context of and specific resources for assessment
This unit may be assessed on the job, off the job or a combination of both on and off the job. Where assessment occurs off the job, that is the candidate is not in productive work, then an appropriate simulation must be used where the range of conditions reflects realistic workplace situations. The competencies covered by this unit would be demonstrated by an individual working alone or as part of a team. The assessment environment should not disadvantage the candidate.
This unit could be assessed in conjunction with any other units addressing the safety, quality, communication, materials handling, recording and reporting associated with setting computer controlled machines/processes or other units requiring the exercise of the skills and knowledge covered by this unit.
Method of assessment
Assessors should gather a range of evidence that is valid, sufficient, current and authentic. Evidence can be gathered through a variety of ways including direct observation, supervisor's reports, project work, samples and questioning. Questioning techniques should not require language, literacy and numeracy skills beyond those required in this unit of competency. The candidate must have access to all tools, equipment, materials and documentation required. The candidate must be permitted to refer to any relevant workplace procedures, product and manufacturing specifications, codes, standards, manuals and reference materials.
Guidance information for assessment
Replaced By
State Code National Code Title Type
OAW39 MEM07015 Set computer controlled machines and processes Unit of competency