Unit of competency Outline
Date retreived
23/07/2026 2:34 AM AWST
23/07/2026 2:34 AM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Set up, operate and maintain mechanical coatings systems
Set up, operate and maintain mechanical coatings systems
Unit of competency
National Code
LMFFF3002B
LMFFF3002B
State Code
W8515
W8515
TGA Status
Replaced
Replaced
DTWD Status
Replaced
Replaced
State Implementation and Classification
Approved Date
19/09/2008
Field of Education
030717 - Plant And Machine Operations
Original Release Date
19/09/2008
Nominal Hours
44
Description
This unit covers the competency to set up, operate and maintain mechanical coating systems in order to apply coatings to specifications.
Notes
Elements and Performance Criteria
1. Prepare for work
- 1.1. Characteristics of the surface and the required surface coating are identified from work orders or instructions
- 1.2. Processing and application techniques, time and safety requirements are identified and used for work planning
- 1.3. OHS requirements, including ventilation requirements and personal protection needs, are observed throughout the work
- 1.4. Tools, equipment and accessories are identified and checked for safe and effective operation for the surface coating task
- 1.5. Coating materials are identified and prepared
2. Check and prepare for spraying
- 2.1. Products with surface or other faults are identified and faults reported or repaired as appropriate
- 2.2. Other products and equipment in the workplace are protected from overspray
- 2.3. Trial applications of surface materials are made to check equipment operation, materials consistency and specified surface finish
- 2.4. Machine faults are identified and rectified or reported
- 2.5. Material faults are identified and workplace procedures for rectification are followed
3. Apply surface coating
- 3.1. Surfaces are kept free of contamination
- 3.2. Surface coatings are applied according to workplace procedures
- 3.3. Surface coating viscosity and coverage is monitored and checked against workplace requirements for even spread and thickness
- 3.4. Rectification of surface faults is made as required
- 3.5. Products are inspected and approved for suitability for further processing
- 3.6. Defects are dealt with and/or reported in accordance with workplace procedures
4. Clean work area and maintain equipment
- 4.1. Equipment is cleaned and inspected for serviceable condition and stored appropriately
- 4.2. Unserviceable equipment is tagged, faults are identified and appropriate personnel are informed
- 4.3. Work area, including spray booth is cleaned and returned to approved condition
- 4.4. Workplace records are completed
RANGE STATEMENT
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Unit context
OHS requirements include legislation, building codes, material safety management systems, hazardous substances and dangerous goods code and local safe operating procedures
Work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements
Work requires individuals to demonstrate discretion, judgement and problem solving skills in the application of surface coatings
Surface coating operations
This unit covers work involved in the application of surface coatings by mechanical methods other than by conventional hand-held spray gun or airless spray gun
Surface coatings are to include: a minimum of two of those required for curtain coating, UV coating, tumbling, dipping and electrostatic powder coating tasks
Tools and equipment are to include:
computerised spray system
electrostatic spray gun
baking oven
barrel tumbler
spray booth
liquid containers
air compressor and hoses
screwdrivers
shifting spanner and spanners
ford cup
Materials to be applied may include but are not limited to:
stains
lacquers
wax
oil
two-pack polyurethane
three-pack polyester
enamels
acrylics
powder coating
Personal protective equipment
Personal protective equipment is to include that prescribed under legislation, regulations and enterprise policies and practices
Information and procedures
Workplace procedures relating to the use of tools and equipment
Work instructions, including job sheets, plans, drawings and designs
Workplace procedures relating to reporting and communication
Manufacturer specifications and operational procedures
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Unit context
OHS requirements include legislation, building codes, material safety management systems, hazardous substances and dangerous goods code and local safe operating procedures
Work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements
Work requires individuals to demonstrate discretion, judgement and problem solving skills in the application of surface coatings
Surface coating operations
This unit covers work involved in the application of surface coatings by mechanical methods other than by conventional hand-held spray gun or airless spray gun
Surface coatings are to include: a minimum of two of those required for curtain coating, UV coating, tumbling, dipping and electrostatic powder coating tasks
Tools and equipment are to include:
computerised spray system
electrostatic spray gun
baking oven
barrel tumbler
spray booth
liquid containers
air compressor and hoses
screwdrivers
shifting spanner and spanners
ford cup
Materials to be applied may include but are not limited to:
stains
lacquers
wax
oil
two-pack polyurethane
three-pack polyester
enamels
acrylics
powder coating
Personal protective equipment
Personal protective equipment is to include that prescribed under legislation, regulations and enterprise policies and practices
Information and procedures
Workplace procedures relating to the use of tools and equipment
Work instructions, including job sheets, plans, drawings and designs
Workplace procedures relating to reporting and communication
Manufacturer specifications and operational procedures
EVIDENCE GUIDE
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Critical Aspects of Evidence
Locate, interpret and apply information relevant to the materials being applied and the application equipment
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Follow work instructions, operating procedures and inspection practices to:
minimise the risk of injury to self and others
prevent damage to goods, equipment and products
maintain required production output and product quality
Select and apply surface coatings, including the adjustment of spray equipment to effect required coating using a minimum of two different mechanical systems:
curtain coater
electrostatic
tumbler
dipping
roller coater (UV)
automatic (robotic) spray equipment
Work effectively with others
Modify activities to cater for variations in workplace contexts and environment
Resource Implications
Mechanical spray systems and equipment, spray booth, coatings and cleaning products.
Method of Assessment
Assessment methods must confirm consistency of performance over time and in a range of workplace relevant contexts.
Assessment should be by direct observation of tasks and questioning on underpinning knowledge.
Assessment may be in conjunction with assessment of other relevant units of competency.
Context of Assessment
Assessment may occur on the job or in a workplace simulated facility with relevant process equipment, materials, work instructions and deadlines.
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Critical Aspects of Evidence
Locate, interpret and apply information relevant to the materials being applied and the application equipment
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Follow work instructions, operating procedures and inspection practices to:
minimise the risk of injury to self and others
prevent damage to goods, equipment and products
maintain required production output and product quality
Select and apply surface coatings, including the adjustment of spray equipment to effect required coating using a minimum of two different mechanical systems:
curtain coater
electrostatic
tumbler
dipping
roller coater (UV)
automatic (robotic) spray equipment
Work effectively with others
Modify activities to cater for variations in workplace contexts and environment
Resource Implications
Mechanical spray systems and equipment, spray booth, coatings and cleaning products.
Method of Assessment
Assessment methods must confirm consistency of performance over time and in a range of workplace relevant contexts.
Assessment should be by direct observation of tasks and questioning on underpinning knowledge.
Assessment may be in conjunction with assessment of other relevant units of competency.
Context of Assessment
Assessment may occur on the job or in a workplace simulated facility with relevant process equipment, materials, work instructions and deadlines.
Replaces
| State Code | National Code | Title | Type |
|---|---|---|---|
| W0262 | LMFFF3002A | Set up, operate and maintain mechanical coatings systems | Unit of competency |
Replaced By
| State Code | National Code | Title | Type |
|---|---|---|---|
| WI322 | MSFFF3002 | Set up, operate and maintain mechanical coating systems | Unit of competency |
| State Code | National Code | Title | Type |
|---|---|---|---|
| W030 | LMF30202 | Certificate III in Furniture Finishing | Qualification |