Unit of competency Outline
Date retreived
23/07/2026 6:09 PM AWST
23/07/2026 6:09 PM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Interpret and apply instructions to install pumps
Interpret and apply instructions to install pumps
Unit of competency
National Code
AHCIRG309A
AHCIRG309A
State Code
WE015
WE015
TGA Status
Replaced
Replaced
DTWD Status
Replaced
Replaced
State Implementation and Classification
Approved Date
11/04/2013
Field of Education
059999 - Agriculture, Environmental And Related Studies, N.e.c.
Original Release Date
11/04/2013
Nominal Hours
45
Description
This Unit covers the process of interpreting instructions to install pumps and defines the standard required to: organise resources for installation work; set out and prepare site; site the pump and place it on a base; connect suction and discharge lines; and commission the pumping system.
Notes
Elements and Performance Criteria
1 Source irrigation system requirements
- 1.1 Location of pump is determined following site inspection
- 1.2 Pump base requirements are identified from drawings and specifications using relevant information
- 1.3 Required materials and equipment are identified, ordered and collected in accordance with workplace procedures
- 1.4 Materials and equipment are checked for compliance with relevant Australian standards, docket and order form, and for acceptable condition
- 1.5 Sustainability principles and concepts are applied to work preparation and application
2 Plan and sequence installation tasks from instructions
- 2.1 Drawings and specifications are obtained
- 2.2 OHS requirements associated with installing water pump sets, and workplace environmental requirements, are adhered to throughout the work
- 2.3 Workplace instructions are identified and adhered to
- 2.4 Tasks are planned and sequenced in conjunction with others involved in or affected by the work and statutory and regulatory authority requirements
- 2.5 Work area is prepared to support efficient installation of water pump sets
3 Select and check tools and equipment for serviceability
- 3.1 Tools and equipment for installing water pumps are selected and checked for serviceability
- 3.2 PPE is selected and used to meet workplace OHS requirements
4 Install and commission pumping and flow control components
- 4.1 Pump base is set out to comply with drawings and specifications
- 4.2 Pump base is constructed in accordance with drawings and specifications
- 4.3 Pump and pump controls are installed in accordance with relevant Australian standards, drawings, specifications and manufacturer instructions
- 4.4 Suction and discharge lines andflow control devices are connected
- 4.5 Delivery and distribution components connected to pump comply with relevant specifications and manufacturer instructions
- 4.6 Pressure testing of pumping system is conducted in accordance with specifications
- 4.7 Pump is tested in accordance with specifications and test data is recorded in required format
5 Clean up after installation
- 5.1 Work area is cleared and materials disposed of, reused or recycled according to legislation, regulations, codes of practice and job specification
- 5.2 Tools and equipment are cleaned, checked, maintained and stored in accordance with manufacturer recommendations and workplace procedures
- 5.3 Documentation is completed in accordance with workplace requirements
6 Review, record and report activities.
- 6.1 Equipment, tools and materials are checked, maintained and stored according to manufacturer guidelines and organisational procedures
- 6.2 Work site is restored to meet environmental and organisational requirements
- 6.3 Activities are recorded and reported according to organisational procedures
The range statement relates to the Unit of Competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
OHS requirements may include:
solar radiation, dust, noise, air- and soil-borne micro-organisms, chemicals and hazardous substances, sharp hand tools and equipment, manual handling, holes, and slippery and uneven surfaces.
Water pump sets may include:
centrifugal
Archimedes screw type
submersible
positive displacement.
Personal protective clothing and equipment (PPE) may include:
steel capped boots/shoes, overalls, gloves, sun hat, sunscreen lotion, safety goggles, face mask and hearing protection, and any protection required for the use of equipment.
Pumping and flow control components may include:
all types of pumps and pumping systems (including filters and valves) used to move water to or through an irrigation system.
Flow control devices may include:
flow directional gates
regulators
valves
sluice
gate
blade
non-return
doors, drop structures and bars.
OHS requirements may include:
solar radiation, dust, noise, air- and soil-borne micro-organisms, chemicals and hazardous substances, sharp hand tools and equipment, manual handling, holes, and slippery and uneven surfaces.
Water pump sets may include:
centrifugal
Archimedes screw type
submersible
positive displacement.
Personal protective clothing and equipment (PPE) may include:
steel capped boots/shoes, overalls, gloves, sun hat, sunscreen lotion, safety goggles, face mask and hearing protection, and any protection required for the use of equipment.
Pumping and flow control components may include:
all types of pumps and pumping systems (including filters and valves) used to move water to or through an irrigation system.
Flow control devices may include:
flow directional gates
regulators
valves
sluice
gate
blade
non-return
doors, drop structures and bars.
The evidence guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Overview of assessment
Critical aspects for assessment and evidence required to demonstrate competency in this Unit
The evidence required to demonstrate competency in this Unit must be relevant to workplace operations and satisfy holistically all of the requirements of the performance criteria and required skills and knowledge and include achievement of the following:
organise resources for installation work
set out and prepare site
site the pump and place it on a base
connect suction and discharge lines
commission the pumping system.
Context of and specific resources for assessment
Competency requires the application of work practices under work conditions. Selection and use of resources for some worksites may differ due to the regional or enterprise circumstances.
Overview of assessment
Critical aspects for assessment and evidence required to demonstrate competency in this Unit
The evidence required to demonstrate competency in this Unit must be relevant to workplace operations and satisfy holistically all of the requirements of the performance criteria and required skills and knowledge and include achievement of the following:
organise resources for installation work
set out and prepare site
site the pump and place it on a base
connect suction and discharge lines
commission the pumping system.
Context of and specific resources for assessment
Competency requires the application of work practices under work conditions. Selection and use of resources for some worksites may differ due to the regional or enterprise circumstances.
Replaced By
| State Code | National Code | Title | Type |
|---|---|---|---|
| BAO98 | AHCIRG309 | Install irrigation pumps | Unit of competency |
| State Code | National Code | Title | Type |
|---|---|---|---|
| J156 | AHC32412 | Certificate III in Irrigation | Qualification |