Unit of competency Outline

Date retreived
24/07/2026 2:22 AM AWST

Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.

Perform eddy current testing

Perform eddy current testing

Unit of competency
National Code
MEM24006
State Code
OEW84
TGA Status
Replaced
DTWD Status
Transition (Replaced)
Current Release Number
1.00
Current Release Date
19/12/2022
View on TGA
State Implementation and Classification
Approved Date
19/04/2023
Field of Education
030305 - Materials Engineering
Original Release Date
19/04/2023
Nominal Hours
54
Description
This unit of competency defines the skills and knowledge required to perform eddy current testing including inspection, interpretation, classification and reporting of results on fabrications, structures and components across a wide range of industries and industrial applications to Level 2 (AS 3669 Non-destructive testing — Qualification and approval of personnel — Aerospace and AS ISO 9712 Non-destructive testing — Qualification and certification of NDT personnel) or equivalent. Eddy current tests are performed on critical component or structural zones. Re-assessment of competency at regular intervals may be required in accordance with Australian Standards or other relevant standards. Actual and potential defects are considered, together with ongoing abnormalities in fabrications, components, structures or aircraft components.Materials and chemicals which are subject to codes and regulations - for example, chemicals, explosives, solvents, dangerous materials, acids, or noxious waste products - are subject to safe work habits and must be stored and used in accordance with safe work practices.Where interpretation of technical drawings is required unit MEM09002 Interpret technical drawing should also be selected.Where the selection and use of engineering measurement is required unit MEM12023 Perform engineering measurements should also be selected.Where the selection and use of power tools are required unit MEM18002 Use power tools/hand held operations should also be selected.No licensing or legislative requirements apply to this unit at the time of publication. Certification against Australian Standards may be achieved where assessment in this unit of competency is carried out in conjunction with an examining authority as described in AS ISO 9712 Non-destructive testing — Qualification and certification of NDT personnel.Band: BUnit Weight: 6
Notes
Elements and Performance Criteria
1. Determine job requirements
  • 1.1 Follow standard operating procedures (SOPs)
  • 1.2 Comply with work health and safety (WHS) requirements at all times
  • 1.3 Use appropriate personal protective equipment (PPE) in accordance with SOPs
  • 1.4 Identify job requirements from specifications
2. Prepare inspection areas for eddy current testing
  • 2.1 Identify inspection areas, clean and prepare for testing using appropriate procedures and materials
  • 2.2 Carry out preparation processes in accordance with the relevant procedures and statutory requirements
  • 2.3 Assess inspection areas visually and identify obvious discontinuities
3. Perform tests
  • 3.1 Select the most appropriate eddy current test for the material and/or application
  • 3.2 Select test equipment and prepare in accordance with standards and/or procedures
  • 3.3 Optimise test set up by calculating effects on probe dimensions, frequency and phase of induced field and material conductivity on eddy current penetration
  • 3.4 Carry out eddy current test in accordance with relevant standards and specifications
  • 3.5 Check eddy current test equipment for defects and maintain and store in accordance with procedures and manufacturer instructions
4. Interpret and report the results of eddy current tests
  • 4.1 Assess indications and detect defects and classify in accordance with national and international codes and standards
  • 4.2 Confirm defects in accordance with organisational procedures and industry practices
  • 4.3 Report test results in accordance with organisational procedures, accepted industry practices and customer service requirements
No information
No information
Replaces
State Code National Code Title Type
W5704 MEM24006B Perform eddy current testing Unit of competency
Replaced By
State Code National Code Title Type
OFH43 MEM24026 Undertake eddy current tests Unit of competency