Unit of competency Outline
Date retreived
22/07/2026 4:09 AM AWST
22/07/2026 4:09 AM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Finish cured concrete products
Finish cured concrete products
Unit of competency
National Code
PMC552053C
PMC552053C
State Code
WA939
WA939
TGA Status
Replaced
Replaced
DTWD Status
Replaced
Replaced
State Implementation and Classification
Approved Date
15/08/2014
Field of Education
030101 - Manufacturing Engineering
Original Release Date
15/08/2014
Nominal Hours
40
Description
This unit of competency covers the finishing of cured concrete products. It involves checking and preparing surfaces, finishing surfaces, cleaning and sealing surfaces and identifying and resolving process malfunctions.
Notes
Elements and Performance Criteria
1. Check product prior to finishing
- 1.1. Check product identity and finish required
- 1.2. Check product has been cured and is ready for finishing
- 1.3. Check type and size of aggregate and any special characteristics of concrete mix
- 1.4. Check for handling and other damage and report if necessary
- 1.5. Set up finishing process as required
2. Undertake initial finishing as required
- 2.1. Perform initial finishing over product surface
- 2.2. Check for consistency, flatness and that other requirements have been met
- 2.3. Report products which are outside specification or which may not be able to be correctly finished
3. Finish surface as required
- 3.1. Adjust finishing process as required
- 3.2. Monitor progress of finishing and readjust as required
- 3.3. Continue finishing until surface meets specification
4. Clean and seal coat as required
- 4.1. Clean finished surface as required
- 4.2. Apply sealer coat as required
- 4.3. Monitor and adjust sealer coating thickness against relevant specification
- 4.4. Lift unit into store in accordance with occupational health and safety (OHS) requirements and support on protective pads
5. Rectify routine problems
- 5.1. Identify the range of faults that can occur during the operation
- 5.2. Determine and rectify fault causes in accordance with procedures/work instructions
- 5.3. Identify and rectify equipment failure causes in accordance with procedures/work instructions
- 5.4. Ensure appropriate records and log books of equipment operations are maintained to meet procedures/work instructions
- 5.5. Identify non-routine problems and report to designated person
6. Control hazards
- 6.1. Identify hazards from the job to be done
- 6.2. Identify other hazards in the work area
- 6.3. Assess the risks arising from those hazards
- 6.4. Implement measures to control those risks in line with procedures
RANGE STATEMENT
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Procedures
All operations are performed in accordance with standard procedures and work instructions
OHS
The identification and control of hazards and the application of OHS to be in accordance with current, applicable legislation and regulations, and company procedures. All work is carried out at all times in accordance with these requirements
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Procedures
All operations are performed in accordance with standard procedures and work instructions
OHS
The identification and control of hazards and the application of OHS to be in accordance with current, applicable legislation and regulations, and company procedures. All work is carried out at all times in accordance with these requirements
EVIDENCE GUIDE
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Overview of assessment
The unit will be assessed in as holistic a manner as is practical and may be integrated with the assessment of other relevant units of competency.
Critical aspects for assessment and evidence required to demonstrate competency in this unit
It is essential that the process be understood and that the importance of critical material properties and surface finishing techniques is known. Competence must be demonstrated in the ability to recognise and analyse potential situations requiring action and then in implementing appropriate corrective action.
Consistent performance should be demonstrated. In particular look to see that:
surface finish matches specification and is consistent
progress is continuously monitored and final finish is approached smoothly and confidently
finished surface is cleaned and sealed as required.
Competence must be demonstrated in the operation of all ancillary equipment to the level required for this unit of competency.
Context of and specific resources for assessment
Assessment will require access to an operating plant over an extended period of time, or a suitable method of gathering evidence of operating ability over a range of situations.
Assessment will occur over a range of situations which will include disruptions to normal, smooth operation.
Simulation or case studies/scenarios may be required to allow for timely assessment of parts of this unit of competency. Simulation should be based on the actual plant and will include 'walk-throughs' of the relevant competency components. A bank of scenarios/case studies/what ifs and questions will be required to probe the reasoning behind observable actions.
Method of assessment
Individual enterprises may choose to add prerequisites and co-requisites relevant to their processes.
Guidance information for assessment
Assessment processes and techniques must be culturally appropriate and appropriate to the language and literacy capacity of the candidate and the work being performed.
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Overview of assessment
The unit will be assessed in as holistic a manner as is practical and may be integrated with the assessment of other relevant units of competency.
Critical aspects for assessment and evidence required to demonstrate competency in this unit
It is essential that the process be understood and that the importance of critical material properties and surface finishing techniques is known. Competence must be demonstrated in the ability to recognise and analyse potential situations requiring action and then in implementing appropriate corrective action.
Consistent performance should be demonstrated. In particular look to see that:
surface finish matches specification and is consistent
progress is continuously monitored and final finish is approached smoothly and confidently
finished surface is cleaned and sealed as required.
Competence must be demonstrated in the operation of all ancillary equipment to the level required for this unit of competency.
Context of and specific resources for assessment
Assessment will require access to an operating plant over an extended period of time, or a suitable method of gathering evidence of operating ability over a range of situations.
Assessment will occur over a range of situations which will include disruptions to normal, smooth operation.
Simulation or case studies/scenarios may be required to allow for timely assessment of parts of this unit of competency. Simulation should be based on the actual plant and will include 'walk-throughs' of the relevant competency components. A bank of scenarios/case studies/what ifs and questions will be required to probe the reasoning behind observable actions.
Method of assessment
Individual enterprises may choose to add prerequisites and co-requisites relevant to their processes.
Guidance information for assessment
Assessment processes and techniques must be culturally appropriate and appropriate to the language and literacy capacity of the candidate and the work being performed.
Replaces
| State Code | National Code | Title | Type |
|---|---|---|---|
| W2663 | PMCOPS253B | Finish cured concrete products | Unit of competency |
Replaced By
| State Code | National Code | Title | Type |
|---|---|---|---|
| BAH43 | PMC552053 | Finish cured concrete products | Unit of competency |
| State Code | National Code | Title | Type |
|---|---|---|---|
| W748 | PMC20110 | Certificate II in Manufactured Mineral Products | Qualification |
| W750 | PMC40110 | Certificate IV in Manufactured Mineral Products | Qualification |
| W749 | PMC30110 | Certificate III in Manufactured Mineral Products | Qualification |