Unit of competency Outline

Date retreived
22/07/2026 1:43 AM AWST

Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.

Install/fit out components

Install/fit out components

Unit of competency
National Code
AUM8092B
State Code
W9206
TGA Status
Replaced
DTWD Status
Replaced
Current Release Number
1.00
Current Release Date
01/09/2008
View on TGA
State Implementation and Classification
Approved Date
09/12/2009
Field of Education
030701 - Mechanical Engineering
Original Release Date
09/12/2009
Nominal Hours
36
Description
This unit describes the application of the required skills and knowledge to install/fit out sub-assemblies and components to truck/bus/trailer assemblies to organisation standards.No licensing, legislative, regulatory or certification requirements apply to this unit at the time of publication.
Notes
Elements and Performance Criteria
1. Select and use tools and equipment
  • 1.1. Tools and equipment are selected to meet job requirements
  • 1.2. Daily maintenance on tools and equipment is performed as specified
2. Select and use nuts, bolts, screws, washers and fasteners
  • 2.1. Nuts, bolts, screws, washers, rivets and fasteners are identified and selected to meet the job requirements as stated in the production schedule
  • 2.2. Nuts, bolts, screws, washers, rivets and fasteners are fitted in the required number to the designated positions stated in the production schedule and associated drawings
3. Install/fit out components and sub-assemblies
  • 3.1. Materials list and drawings are correctly read and interpreted.
  • 3.2. Parts and components are matched with the materials list and are positioned and secured as per job specification
  • 3.3. Installed components and sub-assemblies are inspected and checked for quality and specification
4. Route service lines
  • 4.1. Routing requirements are identified and located on the job according to job requirement
  • 4.2. Service lines are routed, tied and clipped to specification
  • 4.3. Workflow and production schedule are recorded and maintained
5. Select and use adhesives, sealants and solvents
  • 5.1. Adhesives are selected and applied to meet quality control and the job requirements stated in the production schedule
  • 5.2. Solvents are selected and used to remove excess adhesives and sealants to ensure finished product meets organisation quality control standards
  • 5.3. Major spills are reported to the appropriate personnel and cleaned up in accordance with emergency procedures for hazardous materials
spanners,
impact guns
screwdrivers
sockets
torque wrenches
robotic equipment.

glass
soft trim components
mirror
hand rails
seats
accessories
floor coverings.

electrical wiring
pneumatic systems
hydraulic systems.

managers
supervisors
team leaders
team members.

Critical aspects for assessment and evidence required to demonstrate competency in this unit

Evidence of the following is essential:

compliance with relevant legislative, regulations, standards, codes of practice and establish safe practices and organisation policies and procedures for managing personal work priorities
maintaining a working knowledge of current work systems and practices
working and communicating effectively and positively with others involved in the work

applying, within authority, the requirements of the job or work role in relation to:

achieving production goals
achieving work quality goals
responding positively to changing work requirements
contributing effectively to cost reduction initiatives
effectively applying problem solving techniques
modify activities to cater for variations in workplace context and environment
install/fit out components and sub-assemblies in accordance with the production schedule
route service lines
attain quality standards
produce work flow records - paper based / electronic
apply organisation OHS policy and procedures.

Context of, and specific resources for assessment
assessment of the competency should take place in a safe working environment in a passenger motor vehicle manufacturing plant or simulated environment using tools/equipment/machinery required for the production process without undue disruption to the production process
assessment is to occur under standard and authorised work practices, safety requirements and environmental constraints.

Method of assessment

A range of assessment methods should be used to assess practical skills and knowledge. The following examples are appropriate for this unit:

assessment methods must confirm consistency and accuracy of performance (over time and in a range of workplace relevant contexts) together with application of underpinning knowledge
assessment methods must be by direct observation of tasks and include questioning on underpinning knowledge to ensure its correct interpretation and application
assessment may be applied under project related conditions (real or simulated) and require evidence of process
assessment must confirm a reasonable inference that competency is able not only to be satisfied under the particular circumstance, but is able to be transferred to other circumstances.

Replaces
State Code National Code Title Type
W5765 AUM8092A Install/fit out components Unit of competency
Replaced By
State Code National Code Title Type
WE157 AUMGTM2004 Install and fit out components Unit of competency