Unit of competency Outline
Date retreived
22/07/2026 9:31 PM AWST
22/07/2026 9:31 PM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Apply sheet laminates by hand
Apply sheet laminates by hand
Unit of competency
National Code
LMFFM2004B
LMFFM2004B
State Code
W8601
W8601
TGA Status
Replaced
Replaced
DTWD Status
Replaced
Replaced
State Implementation and Classification
Approved Date
03/11/2009
Field of Education
030113 - Cabinet Making
Original Release Date
03/11/2009
Nominal Hours
8
Description
This unit covers the competency to apply laminates by hand, including the preparation, layout, application and finalisation processes
Notes
Elements and Performance Criteria
1. Prepare the work
- 1.1. Work instructions are used to determine job requirements, including: process, materials, finish and quantity
- 1.2. Application sequence is planned
- 1.3. Procedures are determined for checking quality at each stage of the process
- 1.4. Workplace health and safety requirements, including personal protection needs, are observed throughout the work
- 1.5. Suitable work area is selected for the task
- 1.6. Tools and equipment suitable for application are identified and checked for safe and effective operation
2. Layout and prepare materials
- 2.1. Laminates are selected and checked for flaws following work instructions
- 2.2. Laminates are prepared for application and laid out
- 2.3. Suitable joining processes are selected and prepared
3. Apply and/or fit and finish
- 3.1. Laminates are measured, marked and cut to size and applied to the base material
- 3.2. Tools and equipment are used in accordance with workplace procedures, including use of personal protective equipment
- 3.3. Adhesives are applied according to workplace procedures and/or manufacturers' instructions
- 3.4. Final trim and finishing are completed to specifications
- 3.5. Work is checked against required quality standards
4. Finalise operation and maintain equipment
- 4.1. Work area is cleaned, hand and/or power tools and equipment are cleaned, maintained and stored in accordance with workplace procedures
- 4.2. Tools and equipment are cleaned and left in a safe mode
- 4.3. Faulty and/or defective equipment is tagged and reported in accordance with workplace practices
- 4.4. Off-cuts and unused materials are collected and stored for reuse or disposal following workplace procedures
- 4.5. Waste and scrap materials are dealt with following workplace procedures
RANGE STATEMENT
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Unit context
OH&S requirements include legislation, building codes, material safety management systems, hazardous substances and dangerous goods code and local safe operating procedures
Work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements
Work requires individuals to demonstrate some discretion, judgement and problem solving skills in applying laminates by hand
Competency may be demonstrated in workplaces involved in the manufacture of solid timber furniture, domestic furniture, commercial furniture, kitchen and bathroom cabinets and/or furniture components
Tools and equipment may include, but are not limited to:
measuring tapes or rulers
mallets
squares
bevels
chisels
planes
hand saws
power saws
power drills/screwdrivers
pneumatic tools
clamps
screwdrivers
rollers
laminate trimmers and cutters and hand routers
Materials to be used may include but are not limited to:
timber
manufactured board
laminates
timber strips
adhesives and cleaning materials
Personal protective equipment
Personal protective equipment is to include that prescribed under legislation, regulations and enterprise policies and practices
Information and procedures
Workplace procedures relating to use and operation of tools and equipment
Work instructions, including job sheets, plans, drawings and designs
Workplace procedures relating to reporting and communications
Manufacturers' instructions for the use of equipment and materials
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Unit context
OH&S requirements include legislation, building codes, material safety management systems, hazardous substances and dangerous goods code and local safe operating procedures
Work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements
Work requires individuals to demonstrate some discretion, judgement and problem solving skills in applying laminates by hand
Competency may be demonstrated in workplaces involved in the manufacture of solid timber furniture, domestic furniture, commercial furniture, kitchen and bathroom cabinets and/or furniture components
Tools and equipment may include, but are not limited to:
measuring tapes or rulers
mallets
squares
bevels
chisels
planes
hand saws
power saws
power drills/screwdrivers
pneumatic tools
clamps
screwdrivers
rollers
laminate trimmers and cutters and hand routers
Materials to be used may include but are not limited to:
timber
manufactured board
laminates
timber strips
adhesives and cleaning materials
Personal protective equipment
Personal protective equipment is to include that prescribed under legislation, regulations and enterprise policies and practices
Information and procedures
Workplace procedures relating to use and operation of tools and equipment
Work instructions, including job sheets, plans, drawings and designs
Workplace procedures relating to reporting and communications
Manufacturers' instructions for the use of equipment and materials
EVIDENCE GUIDE
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Critical Aspects of Evidence
Interpret work order and locate relevant information
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Follow work instructions, operating procedures and inspection practices to:
minimise the risk of injury to self or others
prevent damage to goods, tools, equipment or products
maintain required production output and product quality
Apply and finish laminates to at least three different surfaces, including at least two requiring laminate edging
Work effectively with others
Modify activities to cater for variations in workplace context and environment
Resource Implications
Access to plans, hand and/or power tools, equipment, laminates and finishing materials, woodworking machinery, and a work area.
Method of Assessment
Assessment methods must confirm consistency of performance over time and in a range of workplace relevant contexts.
Assessment should be by direct observation of tasks and questioning on underpinning knowledge.
Assessment should be conducted over time and may be in conjunction with assessment of other relevant units of competency.
Context of Assessment
Assessment may occur on the job or in a workplace simulated facility with relevant process equipment, materials, work instructions and deadlines.
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Critical Aspects of Evidence
Interpret work order and locate relevant information
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Follow work instructions, operating procedures and inspection practices to:
minimise the risk of injury to self or others
prevent damage to goods, tools, equipment or products
maintain required production output and product quality
Apply and finish laminates to at least three different surfaces, including at least two requiring laminate edging
Work effectively with others
Modify activities to cater for variations in workplace context and environment
Resource Implications
Access to plans, hand and/or power tools, equipment, laminates and finishing materials, woodworking machinery, and a work area.
Method of Assessment
Assessment methods must confirm consistency of performance over time and in a range of workplace relevant contexts.
Assessment should be by direct observation of tasks and questioning on underpinning knowledge.
Assessment should be conducted over time and may be in conjunction with assessment of other relevant units of competency.
Context of Assessment
Assessment may occur on the job or in a workplace simulated facility with relevant process equipment, materials, work instructions and deadlines.
Replaces
| State Code | National Code | Title | Type |
|---|---|---|---|
| W0275 | LMFFM2004A | Apply sheet laminates by hand | Unit of competency |
Replaced By
| State Code | National Code | Title | Type |
|---|---|---|---|
| WI413 | MSFFM2004 | Apply sheet laminates by hand | Unit of competency |
| State Code | National Code | Title | Type |
|---|---|---|---|
| W651 | LMF32109 | Certificate III in Cabinet Making | Qualification |
| W031 | LMF30302 | Certificate III in Furniture Making | Qualification |
| W023 | LMF20302 | Certificate II in Furniture Making | Qualification |
| W032 | LMF30402 | Certificate III in Furniture Making (Cabinet Making) | Qualification |
| W033 | LMF30502 | Certificate III in Furniture Making (Wood Machining) | Qualification |