Unit of competency Outline
Date retreived
23/07/2026 7:37 PM AWST
23/07/2026 7:37 PM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Apply graining and decorative finishes
Apply graining and decorative finishes
Unit of competency
National Code
LMFFF3007B
LMFFF3007B
State Code
W8520
W8520
TGA Status
Replaced
Replaced
DTWD Status
Replaced
Replaced
State Implementation and Classification
Approved Date
19/09/2008
Field of Education
030117 - Furniture Polishing
Original Release Date
19/09/2008
Nominal Hours
40
Description
This unit covers the competency to apply material to a surface to imitate timber grain and decorative (faux) finishes.
Notes
Elements and Performance Criteria
1. Prepare for work
- 1.1. Workplace information, including materials application and safety information, material safety data sheets, is used to inform work practices
- 1.2. Characteristics of the surface and the required surface treatment are identified from work orders or instructions
- 1.3. Processing and application techniques, time and safety requirements are identified and used for work planning
- 1.4. OHS requirements, including ventilation requirements and personal protection needs, are observed throughout the work
- 1.5. Tools, equipment and accessories are identified and checked for safe and effective operation for the task
2. Prepare for application of materials
- 2.1. Surfaces are checked for contamination and correct preparation according to workplace procedures and standards
- 2.2. Products with surface or other faults are identified and faults repaired as appropriate
- 2.3. Materials required to complete the task are identified and prepared.
- 2.4. Trial applications of material are made to check equipment operation, materials consistency, viscosity and sample match.
- 2.5. Faults and or inconsistencies in colour and surface appearance are identified and workplace procedures for rectification and adjustment are followed
3. Apply finishing materials
- 3.1. Techniques for application of graining solution and other finishes are identified.
- 3.2. Materials are applied according to job instructions, material manufacturer specifications and workplace procedures
- 3.3. Finished products are inspected and approved for suitability for further processing
- 3.4. Products which do not meet quality specifications are rectified or tagged for further investigation
4. Clean work area and maintain equipment
- 4.1. Equipment used is cleaned and inspected for serviceable condition and stored appropriately
- 4.2. Unserviceable equipment is tagged, faults are identified and appropriate personnel are informed
- 4.3. Work area is cleaned and returned to approved condition, all areas used for bleaching are washed down with water.
- 4.4. Workplace records are completed
RANGE STATEMENT
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Unit context
OHS requirements include legislation, building codes, material safety management systems, hazardous substances and dangerous goods code and local safe operating procedures
Work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements
Work requires individuals to demonstrate some discretion, judgement and problem solving skills in the application of surface coatings
Graining and decorative finishes are to include:
graining and marbling; and may include:
ragging
stippling
ageing
distressing and others
Surfaces may include but are not limited to:
solid timber
manufactured board
metal
Tools and equipment may include, but are not limited to:
liquid containers
rubber gloves
face masks
spray booths
spray guns
compressor
air lines
brushes
sanding block
brushes
graining tools
Materials to be applied may include but are not limited to:
water
abrasive papers
cotton rags
hessian
lacquer-based wiping stain
polyurethane wiping stain
spirit stain
pigment oil stain
proprietary brand stains
pigments
acrylic paint
enamel
Personal protective equipment includes:
that prescribed under legislation, regulations and enterprise policies and practices
Information and procedures
Workplace procedures relating to the use and operation of tools and equipment
Workplace instructions, including job sheets, plans, drawings and designs
Workplace procedures relating to reporting and communications
Manufacturer recommendations for the use of equipment and materials
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Unit context
OHS requirements include legislation, building codes, material safety management systems, hazardous substances and dangerous goods code and local safe operating procedures
Work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements
Work requires individuals to demonstrate some discretion, judgement and problem solving skills in the application of surface coatings
Graining and decorative finishes are to include:
graining and marbling; and may include:
ragging
stippling
ageing
distressing and others
Surfaces may include but are not limited to:
solid timber
manufactured board
metal
Tools and equipment may include, but are not limited to:
liquid containers
rubber gloves
face masks
spray booths
spray guns
compressor
air lines
brushes
sanding block
brushes
graining tools
Materials to be applied may include but are not limited to:
water
abrasive papers
cotton rags
hessian
lacquer-based wiping stain
polyurethane wiping stain
spirit stain
pigment oil stain
proprietary brand stains
pigments
acrylic paint
enamel
Personal protective equipment includes:
that prescribed under legislation, regulations and enterprise policies and practices
Information and procedures
Workplace procedures relating to the use and operation of tools and equipment
Workplace instructions, including job sheets, plans, drawings and designs
Workplace procedures relating to reporting and communications
Manufacturer recommendations for the use of equipment and materials
EVIDENCE GUIDE
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Critical Aspects of Evidence
Interpret work order and locate and apply relevant information
Apply safe handling requirements for equipment, products and materials
Follow work instructions, operating procedures and inspection practices to:
minimise the risk of injury to self and others
prevent damage to goods, equipment and products
maintain required production output and product quality
Apply graining solution to imitate a minimum of two different timber species
Apply graining solution to imitate a minimum of two different timber species
Apply material to imitate a marble finish and one other finish type
Maintain application equipment
Work effectively with others
Modify activities to cater for variations in workplace contexts and environment
Resource Implications
Hand application equipment, graining solution and coating materials.
Method of Assessment
Assessment methods must confirm consistency of performance over time and in a range of workplace relevant contexts.
Assessment should be by direct observation of tasks and questioning on underpinning knowledge.
Assessment should be conducted over time and will generally be in conjunction with assessment of other relevant units of competency.
Context of Assessment
Assessment may occur on the job or in a workplace simulated facility with relevant process equipment, materials, work instructions and deadlines.
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Critical Aspects of Evidence
Interpret work order and locate and apply relevant information
Apply safe handling requirements for equipment, products and materials
Follow work instructions, operating procedures and inspection practices to:
minimise the risk of injury to self and others
prevent damage to goods, equipment and products
maintain required production output and product quality
Apply graining solution to imitate a minimum of two different timber species
Apply graining solution to imitate a minimum of two different timber species
Apply material to imitate a marble finish and one other finish type
Maintain application equipment
Work effectively with others
Modify activities to cater for variations in workplace contexts and environment
Resource Implications
Hand application equipment, graining solution and coating materials.
Method of Assessment
Assessment methods must confirm consistency of performance over time and in a range of workplace relevant contexts.
Assessment should be by direct observation of tasks and questioning on underpinning knowledge.
Assessment should be conducted over time and will generally be in conjunction with assessment of other relevant units of competency.
Context of Assessment
Assessment may occur on the job or in a workplace simulated facility with relevant process equipment, materials, work instructions and deadlines.
Replaces
| State Code | National Code | Title | Type |
|---|---|---|---|
| W0267 | LMFFF3007A | Apply graining and decorative finishes | Unit of competency |
Replaced By
| State Code | National Code | Title | Type |
|---|---|---|---|
| WI327 | MSFFF3007 | Apply graining and decorative finishes | Unit of competency |
| State Code | National Code | Title | Type |
|---|---|---|---|
| W030 | LMF30202 | Certificate III in Furniture Finishing | Qualification |