Unit of competency Outline
Date retreived
23/07/2026 7:04 AM AWST
23/07/2026 7:04 AM AWST
Whilst all efforts are made to provide accurate and timely information from the relevant source/documentation, please be aware that the information supplied may not be the most current version. The accuracy of the detail has not been confirmed by the Department and therefore should not be relied upon without first confirming the contents.
Construct jigs and fixtures
Construct jigs and fixtures
Unit of competency
National Code
LMFFM3033B
LMFFM3033B
State Code
W8633
W8633
TGA Status
Replaced
Replaced
DTWD Status
Replaced
Replaced
State Implementation and Classification
Approved Date
01/12/2011
Field of Education
030705 - Toolmaking
Original Release Date
01/12/2011
Nominal Hours
34
Description
This unit covers the competency to prepare and construct jigs and fixtures to produce furniture components
Notes
Elements and Performance Criteria
1. Identify the purpose of the jig or fixture
- 1.1. Purpose of the jig or fixture and the equipment it is to be used on is established
- 1.2. Proposed service life of jig or fixture is established
- 1.3. Tolerances allowed are identified
- 1.4. Materials for jig construction are established
- 1.5. Quality requirements for each stage of the construction process are identified
2. Plan jig or fixture construction
- 2.1. Plan of proposed jig or fixture is produced
- 2.2. Approval of design is gained through workplace procedures
- 2.3. Steps or stages in production are planned, noting check points for measurements and tests
3. Collect materials and equipment
- 3.1. Workplace health and safety requirements, including personal protection needs, are observed throughout the work
- 3.2. Sufficient materials to complete the project are assembled ready for use
- 3.3. Suitable work area is selected
- 3.4. Hand and/or power tools are identified and checked for serviceability and assembled in work area
- 3.5. Appropriate equipment required is identified and checked for serviceability
4. Construct the jig or fixture
- 4.1. Production plan is followed to construct the jig or fixture
- 4.2. Tools and equipment are used in accordance with workplace procedures
- 4.3. Quality checks are conducted at the identified points
- 4.4. Modifications are identified and recommended within workplace procedures
- 4.5. Modifications to the plan are documented and followed
- 4.6. Jig or fixture is checked for fitness for purpose
5. Clean up work area and maintain equipment
- 5.1. Any faulty and/or defective equipment is isolated and reported to appropriate persons
- 5.2. Material which can be reused is collected and stored
- 5.3. Waste and scrap are removed following workplace procedures
- 5.4. All tools, equipment and personal protective equipment are cleaned, maintained and appropriately stored
- 5.5. Work area is cleaned in accordance with workplace procedures
RANGE STATEMENT
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Machines for which jigs and fixtures are made may include, but are not limited to:
band saws
cross cut saws
jig saws
mitre saws
panel and rip saws
belt sanders
panel planers
surface planers
horizontal borers
vertical drill presses
mortisers
tenoners
spindle moulders
overhead and inverted pin routing machines
The uses for jigs and fixtures may include, but are not limited to:
holding
shaping
drilling
cutting
routing
Jigs and fixtures are used in the production of, but are not limited to:
chair legs
shaping curved components
end panels
trenching
grooving
Tools and equipment may include, but are not limited to:
measuring tapes or rulers
hammers
mallets
squares
bevels
chisels
planes
hand saws
power saws
power drills/screwdrivers
pneumatic tools
clamps
screwdrivers
pincers
Unit context
OH&S requirements include legislation, building codes, material safety management systems, hazardous substances and dangerous goods code and local safe operating procedures
Work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements
Work requires individuals to demonstrate some discretion, judgement and problem solving skills in the set up and operation of machines
Competency may be demonstrated in workplaces involved in the manufacture of solid timber furniture, domestic furniture, commercial furniture, kitchen and bathroom cabinets and/or furniture components
Material used in the construction of jigs and fixtures may include, but is not limited to:
solid timber
manufactured board
metal
plastics
synthetic solids
laminates and non-ferrous materials
Personal protective equipment
Personal protective equipment is to include that prescribed under legislation, regulations and enterprise policies and practices
Information and procedures
Workplace procedures relating to the use of tools and equipment
Work instructions, including job sheets, cutting lists, plans, drawings and designs
Workplace procedures relating to reporting and communication
Manufacturers' specifications and operational procedures
The range statement relates to the unit of competency as a whole. It allows for different work environments and situations that may affect performance. Bold italicised wording, if used in the performance criteria, is detailed below. Essential operating conditions that may be present with training and assessment (depending on the work situation, needs of the candidate, accessibility of the item, and local industry and regional contexts) may also be included.
Machines for which jigs and fixtures are made may include, but are not limited to:
band saws
cross cut saws
jig saws
mitre saws
panel and rip saws
belt sanders
panel planers
surface planers
horizontal borers
vertical drill presses
mortisers
tenoners
spindle moulders
overhead and inverted pin routing machines
The uses for jigs and fixtures may include, but are not limited to:
holding
shaping
drilling
cutting
routing
Jigs and fixtures are used in the production of, but are not limited to:
chair legs
shaping curved components
end panels
trenching
grooving
Tools and equipment may include, but are not limited to:
measuring tapes or rulers
hammers
mallets
squares
bevels
chisels
planes
hand saws
power saws
power drills/screwdrivers
pneumatic tools
clamps
screwdrivers
pincers
Unit context
OH&S requirements include legislation, building codes, material safety management systems, hazardous substances and dangerous goods code and local safe operating procedures
Work is carried out in accordance with legislative obligations, environmental legislation, relevant health regulations, manual handling procedures and organisation insurance requirements
Work requires individuals to demonstrate some discretion, judgement and problem solving skills in the set up and operation of machines
Competency may be demonstrated in workplaces involved in the manufacture of solid timber furniture, domestic furniture, commercial furniture, kitchen and bathroom cabinets and/or furniture components
Material used in the construction of jigs and fixtures may include, but is not limited to:
solid timber
manufactured board
metal
plastics
synthetic solids
laminates and non-ferrous materials
Personal protective equipment
Personal protective equipment is to include that prescribed under legislation, regulations and enterprise policies and practices
Information and procedures
Workplace procedures relating to the use of tools and equipment
Work instructions, including job sheets, cutting lists, plans, drawings and designs
Workplace procedures relating to reporting and communication
Manufacturers' specifications and operational procedures
EVIDENCE GUIDE
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Critical Aspects of Evidence
Interpret work order and locate and apply information
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Identify materials used in the work process
Follow work instructions, operating procedures and inspection practices to:
minimise the risk of injury to self or others
prevent damage to goods, tools, equipment or products
maintain required production output and product quality
The selection of materials and the construction of a minimum of three different types of jigs/fixtures, including one for a shaping machine and one which is adjustable
Work effectively with others
Modify activities to cater for variations in workplace contexts and environment
Resource Implications
Job context, materials and equipment for jig or fixture construction.
Method of Assessment
Assessment methods must confirm consistency of performance over time and in a range of workplace relevant contexts.
Assessment should be by direct observation of tasks and questioning on underpinning knowledge.
Assessment should be conducted over time and may be in conjunction with assessment of other units of competency.
Context of Assessment
Assessment may occur on the job or in a workplace simulated facility with relevant process equipment, materials, work instructions and deadlines.
The Evidence Guide provides advice on assessment and must be read in conjunction with the performance criteria, required skills and knowledge, range statement and the Assessment Guidelines for the Training Package.
Critical Aspects of Evidence
Interpret work order and locate and apply information
Apply safe handling requirements for equipment, products and materials, including use of personal protective equipment
Identify materials used in the work process
Follow work instructions, operating procedures and inspection practices to:
minimise the risk of injury to self or others
prevent damage to goods, tools, equipment or products
maintain required production output and product quality
The selection of materials and the construction of a minimum of three different types of jigs/fixtures, including one for a shaping machine and one which is adjustable
Work effectively with others
Modify activities to cater for variations in workplace contexts and environment
Resource Implications
Job context, materials and equipment for jig or fixture construction.
Method of Assessment
Assessment methods must confirm consistency of performance over time and in a range of workplace relevant contexts.
Assessment should be by direct observation of tasks and questioning on underpinning knowledge.
Assessment should be conducted over time and may be in conjunction with assessment of other units of competency.
Context of Assessment
Assessment may occur on the job or in a workplace simulated facility with relevant process equipment, materials, work instructions and deadlines.
Replaces
| State Code | National Code | Title | Type |
|---|---|---|---|
| W0307 | LMFFM3033A | Construct jigs and fixtures | Unit of competency |
Replaced By
| State Code | National Code | Title | Type |
|---|---|---|---|
| WI445 | MSFFM3024 | Construct jigs and fixtures | Unit of competency |
| State Code | National Code | Title | Type |
|---|---|---|---|
| W031 | LMF30302 | Certificate III in Furniture Making | Qualification |
| W032 | LMF30402 | Certificate III in Furniture Making (Cabinet Making) | Qualification |
| W033 | LMF30502 | Certificate III in Furniture Making (Wood Machining) | Qualification |
| D674 | LMF20411 | Certificate II in Glass and Glazing | Qualification |